Futaba FF10CHP 2.4GHz 10ch Transmitter & R6014HS 14ch High Speed Receiver w/ Tx Batteries
2.4G FAAST Dettachable TM-10 module! Now Comes with R6014HS High Speed Receiver
You may control your airplanes, helis and gliders all with this single 2.4Ghz radio system!
The software is available in six languages: German, English, French, Italian, Spanish and Dutch.
The 2.4GHz system that offers the impossible: Pro-level features at a sport-system price.
Some people feel that a 2.4GHz system with a built-in module will always offer better response than a modular system. Nothing could be further from the truth.
The 10C is a modular system, yet offers response superior to most “dedicated” systems. Why? Because response doesn’t depend on whether your module is built-in or modular. It depends on whether your signal starts in analog or digital form.
Converting a signal from analog to digital form requires processing time — what you experience as lag. The 10C, on the other hand, was designed with a totally digital data stream. The signal starts digital and stays digital. Since no additional processing is needed, there’s no lag, either — just virtually instantaneous, real-time response.
And because the 10C is modular, you can use the TM-10 module to fly 2.4GHz-equipped aircraft…or replace it with a 35 or 72MHz module, and fly existing models without added equipment or expense.
System Overview
|
Specifications
|
- Big, 160 x 72 LCD with backlighting, adjustable contrast & auto-off
- Dial ‘n Key™ programming w/joystick navigation
- 15-Model memory (expandable w/optional CamPACs)
- 10-character user name
- 10-character model name
- 2048 resolution in FASST 10-channel mode
- Basic & Advanced menus
- Enhanced airplane, heli & glider software
- Smart Switch Technology™ (SST) — Logic Switches allow you to activate a function when specified switch and/or stick positions occur
- Up/down on/off timer (activate by stick or switch)
- Tracks service hours for radio and models
- Mode 1-4 selectable (Modes 3 & 4 programmable)
- Assignable functions/switches
- Auxiliary channel screen — for 1-step function/switch assignment & eliminating unused auxiliary functions
- 2 proportional slider switches
- Digital trims on all 4 main channels
- Trim memory & sub-trims (all channels)
- Adjustable trim steps (1-40)
- Fail-safe, servo reversing & EPA
- “Full Functionality” trainer system (cord required)
- Flap switch (3-position)
- Retract switch
- Rotary Dial (3)
- Adjustable Throttle Cut/Idle Down
- Sticks w/length & tension adjustments
- Servo cycle w/bar graph displays
- Constant trim, voltage, name and timer display
- CE Certificated
Enhanced Features:
- Slider Switches
- Rotary Dials
- More Programmable Mixes
- More Factory-Defined Mixes
- R6014HS Receiver
- TM-10 2.4GHz Transmitter Module
|
Advanced Airplane Menu
- 8 Programmable Mixes (4 linear/ (4) w/5-point curves)
- 9 Factory-Defined Mixes: Elevator-Flap; Ailvator (for dual elevator servos); Throttle-Needle; Aileron Differential; Flaperon; V-Tail; Elevon; Snap Roll; and Air Brake w/elevator delay
- Dual/Triple rates (4 ch.)
- Exponential (4 ch.)
- Idle down
- Throttle cut
- Throttle delay
- Throttle Hold & Idle-up w/delay
- 2 independent gyro settings
- 7-point throttle curve
- Flap trim
Advanced Heli Menu
The 10C accepts separate gyro sensitivity, governor speed and servo travel rates for up to 4 flight modes — and automatically changes all three when the flight mode changes.
- 6 Programmable Mixes (4 linear/ (2) 5-point curves)
- 8 Factory-Defined Mixes: Hover-Throttle; Hover-Pitch; Throttle-Needle; Governor; Offset; Revo (5-pt.); Delay; and Throttle Mix (ail/ele/rdr)
- Gyro menu
- 8 swash plate types w/graphics
- Swash Plate AFR
- 7-point throttle curves and (5) (including throttle hold) 7-point pitch curves
- Adjustable High/Low pitch setting
- 3 Adjustable Idle-up conditions
Advanced Glider Menu
- 8 Programmable Mixes (4 linear/ 5-point curves)
- 12 Factory-Defined Mixes: Butterfly-Elevator; Elevator-Flap; Chamber Mix (w/ail/ele/rdr adj.); Aileron-Flap; Aileron-Rudder; Flaperon; V-Tail; Flap Trim; Butterfly w/spoiler adj; and 4-point Offset (w/camber adj. for basic/launch/thermal/speed)
- Adjustable spoiler
- Adjustable Throttle Cut
- Single/Dual Aileron and Flap Servo Selections
- Start, Speed, Distance & Landing conditions, Adjustable Airbrake Activation
- Adjustable Motor Cut
|
Combo Includes:
- T10CHP Transmitter (heli mode with dettachable TM-10 module)
- R6014HS 14ch 2.4GHz Receiver NEW!
- TM-10 2.4GHz RF Module (5-pin)
- Wall Charger FBC-18C(4) or compatible charger, 230V EU plug (110V US/JP charger has been SOLD OUT)
- 700mAh Transmitter Battery NT8S700B
- On/Off Switch Harness, FUTM4385
NEW! R6014HS Receiver:
R6014HS is a new version 2.4Ghz Receiver from Futaba. It could be operated in Normal Mode or High Speed mode. The Normal Mode accepts any type of servos or the peripherals as the frame rate of the output is 14ms. The High Speed Mode accept the digital servos for outputs from 1ch to 6 ch, including BLS Series, and most peripheral equipments such as the gyro or brushless ESCs. The frame rate of the outputs is 7ms. The R6014HS is comptaible with the Fasst Transmitters with TM8 ( on 8Ch mode), TM10 (on 10Ch Mode), TM14 (on multi-ch mode)
Specification for Transmitter T10C:
Operating System: 2-Stick, 10-channel, PCM1024 or FASST-2.4G System
Modulation: 2.4G-10ch (default), 2.4G-7ch / FM(PPM) or PCM Switchable
Power supply: 9.6V, NT8S700B included
Standard Wall Charger:
Input: 220V AC 50Hz 7W (default)
or input: 120V AC 60Hz 7W (by request)
Output: TX 9.6VDC 70mA
RX 4.8VDC 100mA
Stock #FUTL9250, FUTL9251, FUTL925, FUTK9251
Note:
This product is CE certified. NO SERVO is bundled with this combo.
This product must be shipped with INSURED AirParcel or EMS (Free upgrade to DHL for most EU regions), please select EMS when you checkout if you are not sure whether your region supports insured airparcel or not. You may also contact us to confirm before you place the order. Safe packing weight: 3KG, you may ship it together with other products.
10CAP and 10CHP are interchangeable, please write in the comment during checkout if you want to specify the model.
Our 2.4Ghz Futaba transmitters & receivers are globally compatible. That means they can be linked with any 2.4Ghz Futaba transmitter or receiver sold in other regions. (e.g. our transmitter with US receiver)
Our Futaba products are directly manufactured by Futaba Corporation (双葉電子工業株式会社). RC711 is not the affiliate of Hobbico, Inc in the United States.
Subject to availability, we will refund you the total charge + shipping if we cannot ship out this product to you in 7 days.
|
Special CNY Pak 2012! 
