Expert Built Service! ALIGN T-Rex 600E PRO DFC Flybarless Helicopter + 2.4Ghz Futaba/JR Transmitter & Receiver RTF Custom Combo with 22.2V 3300mAh 6S1P 35C Li-Po x 2 + 7.4V 2200mAh Rx battery
New RTF combo with the new DFC Flybarless system DS615 and DS655 servos!
2012-Nov: Upgraded to T-Rex 600E PRO DFC heli RTF, but price remains unchanged!
Fully Setup by One of the Hong Kong's Champion Pilot, Mr Sunny Wong!
Ready-to-Fly with 3 Flying Modes: Beginner, Mid-3D and Hard-3D!
What is RC711's Expert Build Service?
Very different from other assembled RTF set, our Expert Build Service (E.B.S.) will send your helicopter to the expert team who consists of the several champion pilots of Hong Kong's F3D R/C helicopter competition. The expert team will setup your helicopter in 3 modes: Beginner, Mid-3D and Hard-3D which you can choose from the soft menu of your transmitter. This provides an upgrade path for you to learn and practice your flying skills in different stages. Your helicopter will be fully tested outdoor to make sure all modes are properly setup, 100% ready to fly and the build time will be about 1.5 week per helicopter.
The Most Reliable Futaba Radios...
With the all new 2.4Ghz Futaba and JR radio systems, you can have more comprehensive setup for your helicopter from normal beginner flying to extreme 3D flying. You won't waste the Futaba/JR transmitter because you can use it later when you upgrade your helicopter to all other popular models. You can even use it on airplanes!
3 Different Flying Modes for Different Levels:
Our 3D Master uses the idle switch functon on the transmitter to pre-define the 3 different flying modes for your helicopter. This make the helicopter ready for all types of pilots, no matter if you are beginner, intermediate or pros! You can change between different fly modes during a single flight without the need to land the helicopters.
- Beginner (normal) – Normal hovering and fly around. Good for beginner to learn and practice.
- Mid-3D (idle1) – Performance flight. Fly around, 3D fly and invert fly. The next step for intermediate pilots.
- Hard-3D (idle2) – Extreme performance. Super reactive 3D fly. Ready for competition!
*Futaba 6EX transmitter only support 2 modes - normal and idle.
1.Equipped with the low CG DFC rotor head, effectively reduce wind resistance during flight, providing the most direct and precise control feel back to the pilot, and exhibits exhilarating 3D performance and unimaginable flight speed.
2.The frame utilizes 2mm carbon fiber plates of the highest spec. Patented composite material construction technique cleverly utilize frame space that improved overall rigidity, and also created a minimalistic beauty.
3.Innovative sliding battery tray rails imbedded into the 3K side frames, with patented spring loaded latching mechanism, allowing for quick battery access as well as battery protection.
4.Heatsink embedded into motor mount for effective cooling of motor.
5.Top mounted motor base bringing the motor’s center of gravity closer to rotating disc, improving 3D agility.
6.Utilize direct link CCPM swashplate control system to enable direct and fast control response. Specially designed anodized CNC servo horns are not only visually pleasing, but are extremely rigid.
7.Utilizes highest spec CNC modue-1 helical main gear, with highest load tolerance and lowest noise.
8.The most optimal motor pinion ratio and tail gear ratio to achieve the most efficient power output and flight characteristic.
9.High quality 5mm carbon rod and CNC metal tail scissor control arms are used in rudder control system to improve rudder lockingand control effectiveness.
10.Additional radial bearing is added to the one way bearing block to ensure smooth rotation, and eliminate jammed one way bearing.
11.Brand new 600 class 12S high voltage brushless motor providing generous torque and power output, yet consumes lower average current to prolong the life of batteries
12.Motor mount consists of third bearing block to provide motor shaft support, effectively reduce torque induced shifts, and minimize gear striping issue.
13.High quality new tail gearbox design, combined with new dual point mounted tail pitch control assembly to minimize slops and increase rudder control precision.
14.Brand new CNC machined metal tail gear box, with thicker side plates to increase rigidity. The more streamlined design also allows for simpler disassembly.
15.Total pitch range of +15~-15 degrees, for the ultimate 3D explosive power.
16.Tail pitch mechanism equipped with high precision bearing.
17.High speed thrust bearings in tail blade grips.
18.New lightened landing gear assembly with lower center of gravity.
19.High quality painted fiberglass canopy with 4-point quick release mounts.
Users must have a certain concept of security to operate the R/C helicopters.
Be sure to read and comply with related safety notes of instruction manual before flying.
● Length: 1174mm
● Height: 319mm
● Width: 210mm
● Main Blade Length: 600mm
● Main Rotor Diameter: 1347mm
● Tail Rotor Diameter: 260mm
● Motor Drive Gear:13T
● Main Drive Gear:112T
● Autorotation Tail Drive Gear: 131T
● Tail Drive Gear: 34T
● Drive Gear Ratio: 1:8.61:3.85
● Weight(With Motor): 2290g
●Align T-REX 600E PRO DFC Helicopter (Fully Assembled, Ready-to-Fly) X1
●600 3G Carbon fiber blades x 1 (installed)
●600MX Brushless Motor(510KV) x 1 (installed)
●DS615 Digital servo x 3 (installed)
●DS655 Digital servo x 1 (installed)
●Castle Phoenix ICE2 HV 80 Brushless ESC x 1 (installed)
●6A External BEC w/ 5.1V Two-way Step-down voltage regulator x 1 (installed)
●Extra! RAIDEN 22.2v 3300mAh 6S1P 35C Li-Polymer battery x 2
●Extra! RAIDEN 7.4V 2200mAh 25C Li-Po Battery for Receiver y x 1
●Extra! Y-cable for batteries
Radio Combo Included:
●Choices of 2.4Ghz Futaba or JR Transmitter
●Choices of 2.4Ghz Futaba or JR Receiver
●Rechargable Battey for Transmitter (not included in some radio models)
●220V Charger for Transmitter Battery Only. (100V-240V for JR radios)
●English Instruction Manual
●Other Accessories (different for each radio model)
|Focus Shot1(Equipped with the low CG DFC rotor head, exhibits exhilarating 3D performance and unimaginable flight speed)
||Focus Shot2(Top mounted motor base and imbedded servo mounts )
||Focus Shot3(New lightweight H-cross section for electronic equipments)
|Focus Shot4(Sliding battery tray rails imbedded into 3K Side frame)
||Focus Shot5(CNC slant thread main drive gear set)
||Focus Shot6(CNC machined aluminum pieces including servo mount)
|Focus Shot7(Rudder servo mount imbedded into 3K Side frame)
||Focus Shot8(New carbon tail control pushrod assembly)
||Focus Shot9(.New tail control assembly with dual mounting points, effectively eliminate slop and improve control precision and feel)
|Focus Shot10(600MX 510KV Brushless Motor)
||Focus Shot11(600 3G Carbon fiber blades)
||Focus Shot12(DS615 standard servo)
|Focus Shot13(DS655 servo)
||Focus Shot14(Castle ICE2 HV 80 Brushless ESC)
||Focus Shot15(3GX Flybarless System)
|Focus Shot16(6A External BEC w/ 5.1V Two-way Step-down voltage regulator )
- The E.B.S.'s lead time is about 1.5 weeks. The order will be shipped out 1.5 weeks after order placed and payment received.
- Please check with us for the availability of the radio model before order. Usually Futaba radios are available all the time.
- We will pack the RTF helicopter together with the radio into a hard paper box with a lot of protection. Since the size of the parcel is quite large, we do not offer free DHL upgrade for EMS order of this product.
- This RTF combo can be shipped with air parcel with XP-size. However some countries have restricted the parcel to P-size which is too small to contain the T-Rex 550E RTF. If you are not certain, please email us with your full shipping address. We will get back to you with the suggested shipping method ASAP.
- Balance charger is not included. For high capacity Li-Po battery, we suggest to use the intelligent multifunction charger - e.g. iMAX B5/B6, E605 and etc...